The Smardt Technical Training course is a four day program designed to equip technicians with the skills and tools necessary to service and maintain Smardt products. The certification received upon completion of this course authorizes the participants to carry out regular maintenance and basic troubleshooting of Smardt equipment but does not certify them as a third party trainer on Smardt, Kiltech, or DTC equipment nor does it grant permission to start Smardt chillers unassisted. Certification will remain valid for a period of 18 months, after which, Smardt reserves the right to require additional advanced or refresher training in order to maintain certification.
Smardt reserves the right to enroll applicants from multiples organizations in any course administered by Smardt and the right to reject applicants or refuse certification, at its sole discretion, if the contractor or technician pre-requisites listed below are not met.
Participants are required to bring a laptop computer that either runs or can emulate Windows 32 bit Operating System (OS) as well as open PDF and MS Office documents. Please note that Windows 8 has not been tested with any of Smardt’s products yet.
Participants must also have access to and be able to operate a mobile internet device when servicing Smardt equipment.
The cost for the four day course is $2,500.00 and is due prior to arrival. All figures are in US dollars, are inclusive of all applicable taxes, and are per person per company. Travel, accommodations, and transportation are the responsibility of the participants. Upon request Smardt will provide hotel, restaurant, and travel recommendations.
A cancellation fee of 30% will apply if attendance is cancelled within 30 calendar days of a scheduled course, 60% if cancelled within 14 calendar days, and 100% if cancelled within 7 calendar days or in the case of an absence.
Smardt reserves the right to cancel a scheduled course if enrollment is insufficient. Smardt will provide written notice of its intention to cancel a minimum of two weeks prior to the scheduled course date. Please confirm scheduling with the Product Support department prior to making your travel arrangements.
- Clean tubes/coils
- Leak check complete chiller
- Reclaim chiller refrigerant charge
- Evacuate chiller below 500 microns
- Replace compressors/components
- Documented Education or related work experience (1 of the following 4)
- Engineering Degree
- Associates Degree
- Professional Certificate
- Trade Papers
- 5 yrs minimum experience with Centrifugal chillers
- Adequate Computer Skills
- Familiar with Microsoft Windows
- Familiar with Microsoft Office
- Able to copy/paste files/folders
- Able to open, create, and save files
- Able to capture screen shots
- Able to download and install software
- Familiar with basic multimeter functions
- Measuring resistance
- Measuring voltage
- Measuring amperage
- Measuring milli-amperage
- Measuring continuity
- Measuring diodes
- Measuring capacitance
- Ability to read P&ID documents
- Previous electrical experience/training
- Previous VFD experience/training
- Previous controls experience/training
The four day course covers the revolutionary Danfoss Turbocor compressor technology, the innovative Kiltech controller, and the energy efficient Smardt chiller family. Each day begins at 9am and lasts for approximately seven hours including a one hour lunch.
- Company Overview/Technology history
- DTC Compressor Overview
- Compressor key features
- Discussion on centrifugal compressors
- Compressor in-depth
- Compressor operation
- Kiltech Controller Overview
- Kiltech controller setup
- Software installation
- Data retrieval
- Chiller component overview
- Factory tour/chiller test run
- DTC Service Monitoring Tool (SMT) Installation
- STC SMT Overview
- Compressor Troubleshooting
- Technical Literature Familiarization
- Smardt Forms and Procedures
Application forms are available below. Please complete and submit the online form or complete and return the PDF to the attention of the Support Department via fax (514) 683-6013 or email: [email protected]
Technical Training Booking Form (39Kb)
Scheduled Training Classes
The following technical training class dates have been tentatively scheduled and are subject to change. Please use these as a guide only, and wait for confirmation from Smardt prior to making any flight or hotel reservations. Smardt reserves the right to cancel any training classes or to schedule additional classes as it sees fit.
|2017-08-22||2017-08-25||Montreal||Spaces : 12|
|2017-10-03||2017-10-06||Montreal||Spaces : 12|
|2017-11-14||2017-11-17||Montreal||Spaces : 12|
|2017-12-05||2017-12-08||Montreal||Spaces : 12|
|2017-10-24||2017-10-27||Montreal||Spaces : 12|
|2017-06-13||2017-06-16||Montreal||Spaces : 11|